Technische Universität Bergakademie Freiberg

Permanent URI for this communityhttp://opara.zih.tu-dresden.de/handle/123456789/16

Research data repository of Freiberg University of Mining and Technology.

Browse

Browsing Technische Universität Bergakademie Freiberg by Author "Bock-Seefeld, Benjamin"

Filter results by typing the first few letters
Now showing 1 - 2 of 2
  • ItemPublic Metadata
    SPP 2419: 3D printing of alumina components via Fused Granulate Fabrication technology and solvent-free debinding of highly filled feedstocks comprising (LD)-polyethylene and cellulose
    (Technische Universität Bergakademie Freiberg, 2026-03-30) Brachhold, Nora; Heuer, Claudia; Bock-Seefeld, Benjamin; Kaiser, Patricia; Weigelt, Christian; Malczyk, Piotr; Trimis, Dimosthenis; Aneziris, Christos G.
    This study focuses on the development of components in gyroid structure based on alumina as integral part of the novel burner designed for the non-premixed combustion of ammonia. During application, the component has to withstand repeated thermal shocks of approx. 600 K or more. Due to the high geometric complexity of the gyroid structure and the need for lightweight design with both macroporous regions and microporous features only the 3D printing was suitable as manufacturing technology; in the present work Fused Granulate Fabrication was used. The manufacturing routine for the employed granules with special regard to the binder system is developed. A customized thermal debinding regime without wick or solvent debinding is presented. Challenges such as the formation of bubbles and the swelling of the samples during thermal debinding were met by adjusting the printing parameters to create porosity and cavities between the deposited strands during 3D printing. Sintered bars fabricated using optimized printing parameters had a shrinkage of 13 %, an open porosity of 41 % and a flexural strength of 50 MPa, respectively. These values are sufficient for the application of the components in the novel burners. As last part of this work sheet-gyroid structures were prepared using a 1.0 mm and 0.4 mm nozzles. These structures successfully survived 5 thermal shock cycles, each involving heating to 1100 ◦C followed by air quenching, which is an excellent result in terms of thermal shock performance.
  • ItemPublic Metadata
    SPP 2419: Investigation of the (thermo-)mechanical properties and the chemical resistance towards ammonia combustion atmosphere of alumina-based model structures manufactured via Fused Granulate Fabrication
    (Technische Universität Bergakademie Freiberg, 2026-06-17) Brachhold, Nora; Bock-Seefeld, Benjamin; Kretzler, Daniel; Heuer, Claudia; Neumann, Marc; Hubálková, Jana; Stelzner, Björn; Stein, Oliver T.; Trimis, Dimosthenis; Aneziris, Christos G.
    This study focuses on the fabrication of alumina-based model samples by fused granulate fabrication for the application in burner components for ammonia combustion. Three compositions were investigated: Two alumina systems with different initial grain size (A1-tabular alumina, A2-reactive alumina) and alumina (AZT) with MgOstabilized ZrO2- and TiO2-additions. Young’s modulus and flexural strength were determined after sintering and after up to five thermal shocks. A1 exhibited the best suitability for repeated thermal shocks, followed by A3. The high interparticle porosity of A1 limited crack propagation and resulted in a slow, gradual loss in elastic modulus (maximum loss of 8.6%) and strength (maximum loss of 35.7%) with increasing number of thermal shocks. Microstructural features due to the additive manufacturing process could enhance thermal shock performance. The materials were tested in ammonia combustion atomosphere at approx. 1500 ◦C for 1 h and showed no phase alterations. Model components with application-near geometries were successfully realized.